From: Robert Botha (flash_at_flash.za.org)
Date: 2002-07-25 21:25:12 UTC
Any way to get the Primary Firmware uploaded into RAM ?
Secondary works fine, but Primary give me this error:
--- #./prism2_srec wlan0 AK010100.HEX srec summary for AK010100.HEX Component: 0x0015 1.1.0 (primary firmware) Supported platforms: 0x800c 1.0.0, 0x8013 1.0.0, 0x8017 1.0.0, 0x801b 1.0.0, 0x8022 1.0.0 Separate S3 data areas: addr 0x007E0000..0x007E0935 (len 2358) addr 0x007E0A00..0x007E131F (len 2336) addr 0x007E17FE..0x007E17FF (len 2) Total data length: 4696 bytes Start address 0x003f0000 Wireless LAN card information: Components: NICID: 0x8013 v1.0.0 PRIID: 0x0015 v1.0.7 STAID: 0x001f v1.3.5 Verifying update compatibility and combining data: PDR 0x0003 not found from wlan card PDA. Using default data. len=12: 39 39 53 41 30 31 30 30 30 30 30 30 PDR 0x0005 not found from wlan card PDA. Using default data. len=2: 00 01 PDR 0x0408 not found from wlan card PDA. Using default data. len=2: 64 00 Plug record length mismatch (PDR=0x0001): 12 != 16 Incompatible updata data. --- Thanx, Robert -----Original Message----- From: Jouni Malinen [mailto:jkmaline_at_cc.hut.fi] Sent: 24 July 2002 23:55 To: hostap_at_lists.ssh.com Subject: Re: Host AP mode with STA f/w v1.4.x On Wed, Jul 24, 2002 at 07:35:36PM +0300, Jouni Malinen wrote: > While testing this, I also noticed that I have managed to break download > support in the latest CVS version.. ;-) Anyway, I'm using a semi-fixed > version in testing and will commit this to CVS after cleaning it up a > bit. This is now fixed in CVS. If you would like to test RAM downloadable secondary firmware, here are some example commands and dmesg output for this:
# compile kernel with download support (currently only for RAM download)
make pccard EXTRA_CFLAGS="-DPRISM2_DOWNLOAD_SUPPORT" sudo make install_pccard
# initializing card normally with flash versions
NIC: id=0x800c v1.0.0 PRI: id=0x15 v1.1.0 STA: id=0x1f v1.4.2
# just show firmware image info
utils/prism2_srec wlan0 RF010409.HEX
# this should tell which component is in question (station firmware
# v1.4.9) and which platforms (NICID) are supported. After showing
# firmware image info, the program compares requirements with the
# initialized card. If everything is OK, the output should end in "OK.".
# load the firmware image into card RAM and start using new version
utils/prism2_srec -r wlan0 RF010409.HEX
# after "OK.", the download starts "Downloading to volatile memory
# (RAM)."
# dmesg output shows download command and the memory areas. It then
# initializes the card again, but stops initialization early and starts
# writing image to card RAM ("Writing # bytes at 0x#"). After all data
# has been initialized, the card is re-initialized again, but this time
# with the downloaded image:
NIC: id=0x800c v1.0.0 PRI: id=0x15 v1.1.0 STA: id=0x1f v1.4.9 Version 1.4.2 did not work in Host AP mode, but the same card works fine after this RAM download. One thing to note about this is that the image loaded to RAM will disappear in next reset (whether it is card removal or recovery attempt of some error state) and prism2_srec needs to be re-run to update the image again. -- Jouni Malinen PGP id EFC895FA